Evening all,

I after some help if I may...

I have an WIC1 ADSL connected from BT and f0/0 connected to a switch which then has a host connected...

The routers activity light is now blonking away which is a good sogn but im getting no internet I can ping my router from my host pc connected to the switch.. can anyone help?

I am a beginer at this so any help is appreciated.


LDIS-ROUTER#show run
Building configuration...

Current configuration : 1743 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname LDIS-ROUTER
!
boot-start-marker
boot-end-marker
!
logging buffered 16256 debugging
logging rate-limit 15
enable secret 5 $1$bAyj$J5deCVkquqLJvrbdWf2OX0
!
no aaa new-model
!
resource policy
!
clock timezone GMT 0
mmi polling-interval 60
no mmi auto-configure
no mmi pvc
mmi snmp-timeout 180
ip subnet-zero
no ip source-route
ip cef
!
!
!
!
no ip bootp server
!
!
!
!
interface FastEthernet0/0
description LAN
ip address 192.168.1.254 255.255.255.0
ip nat inside
speed auto
full-duplex
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface ATM0/0/0
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
no ip mroute-cache
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
!
!
interface Dialer1
description WIC1-ADSL dialer to BT
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
encapsulation ppp
dialer pool 1
dialer idle-timeout 0
dialer-group 2
no cdp enable
ppp chap hostname bthomehub@btbroadband.com
ppp ipcp dns request accept
ppp ipcp route default
ppp ipcp address accept
!
router rip
version 2
network 86.0.0.0
network 192.168.1.0
no auto-summary
!
ip classless
!
no ip http server
ip nat inside source list 1 interface Dialer1 overload
!
access-list 1 permit 192.168.1.0 0.0.0.255
dialer-list 2 protocol ip permit
!
control-plane
!
banner motd ^C
^C
!
line con 0
exec-timeout 20 0
password cisco
logging synchronous
login
line aux 0
line vty 0 4
exec-timeout 20 0
password cisco
logging synchronous
login
!
end

you need this:




Also have you set your password?

_________________
www.mellowd.co.uk/ccie/

He doesn't need a default route as he has:



Can you post the routing table from the device and also try and run a ping to somewhere like 8.8.8.8

_________________
---
David
CCIE R&S #38338, CCIP, CCNP

http://networkbroadcast.co.uk - My Blog
http://twitter.com/davidrothera

Thanks guys,

I can't find the Bt password anywhere on the old home hub... I thought that may be 1 of possibly a few issues. Any clue where I'll find this of the default Bt homebub password? I'm told by default the bthomehub@btbroadband.com is set without one.

I'll get that routing table up tomorrow and try a ping.

You should be able to tell if the issue is not having a password by running 'debug ppp negotiation' and posting it up here if you need a hand.

_________________
---
David
CCIE R&S #38338, CCIP, CCNP

http://networkbroadcast.co.uk - My Blog
http://twitter.com/davidrothera

Plenty of info on the debugger... thanks for the help.

show ip route and ping below....

LDIS-ROUTER#
*May 12 14:27:48.755: %LINK-3-UPDOWN: Interface ATM0/0/0, changed state to up
*May 12 14:27:49.755: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/0/0, changed state to up
LDIS-ROUTER#show ip rout
LDIS-ROUTER#show ip route
Codes: C - connected, S - static, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2
i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
ia - IS-IS inter area, * - candidate default, U - per-user static route
o - ODR, P - periodic downloaded static route

Gateway of last resort is not set

C 192.168.1.0/24 is directly connected, FastEthernet0/0
LDIS-ROUTER#
*May 12 14:27:56.539: %DIALER-6-BIND: Interface Vi2 bound to profile Di1
LDIS-ROUTER#
*May 12 14:27:56.543: %LINK-3-UPDOWN: Interface Virtual-Access2, changed state to up
LDIS-ROUTER#


LDIS-ROUTER#ping 8.8.8.8

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 8.8.8.8, timeout is 2 seconds:
.....
Success rate is 0 percent (0/5)

LDIS-ROUTER#debug ppp negotiation
PPP protocol negotiation debugging is on
*May 12 14:29:43.631: Vi2 LCP: TIMEout: State Listen
*May 12 14:29:43.631: Vi2 PPP: No remote authentication for call-out
*May 12 14:29:43.631: Vi2 LCP: O CONFREQ [Listen] id 95 len 10
*May 12 14:29:43.631: Vi2 LCP: MagicNumber 0x233685BD (0x0506233685BD)
*May 12 14:29:43.855: Vi2 LCP: I CONFREQ [REQsent] id 90 len 19
*May 12 14:29:43.855: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:43.855: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:43.855: Vi2 LCP: MagicNumber 0x724D69A5 (0x0506724D69A5)
*May 12 14:29:43.855: Vi2 LCP: O CONFACK [REQsent] id 90 len 19
*May 12 14:29:43.855: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:43.855: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:43.855: Vi2 LCP: MagicNumber 0x724D69A5 (0x0506724D69A5)
*May 12 14:29:43.855: Vi2 LCP: I CONFACK [ACKsent] id 95 len 10
*May 12 14:29:43.855: Vi2 LCP: MagicNumber 0x233685BD (0x0506233685BD)
*May 12 14:29:43.855: Vi2 LCP: State is Open
*May 12 14:29:43.855: Vi2 PPP: Phase is AUTHENTICATING, by the peer
*May 12 14:29:43.863: Vi2 CHAP: I CHALLENGE id 1 len 35 from "bras-red1.nt-b"
*May 12 14:29:43.863: Vi2 CHAP: Unable to authenticate for peer
*May 12 14:29:43.863: Vi2 PPP: Sending Acct Event[Down] id[31]
*May 12 14:29:43.863: Vi2 PPP: Phase is TERMINATING
LDIS-ROUTER#no debug ppp negotiation
*May 12 14:29:43.863: Vi2 LCP: O TERMREQ [Open] id 96 len 4
*May 12 14:29:43.871: Vi2 LCP: I TERMACK [TERMsent] id 96 len 4
*May 12 14:29:43.871: Vi2 LCP: State is Closed
*May 12 14:29:43.871: Vi2 PPP: Phase is DOWN
*May 12 14:29:43.871: Vi2 PPP: Phase is ESTABLISHING, Passive Open
*May 12 14:29:43.871: Vi2 LCP: State is Listen
*May 12 14:29:43.875: Vi2 LCP: I TERMREQ [Listen] id 1 len 4
*May 12 14:29:43.875: Vi2 LCP: O TERMACK [Listen] id 1 len 4
LDIS-ROUTER#no debug ppp negotiation
*May 12 14:29:45.871: Vi2 LCP: TIMEout: State Listen
*May 12 14:29:45.871: Vi2 PPP: No remote authentication for call-out
*May 12 14:29:45.871: Vi2 LCP: O CONFREQ [Listen] id 97 len 10
*May 12 14:29:45.871: Vi2 LCP: MagicNumber 0x23368E7E (0x050623368E7E)
*May 12 14:29:46.167: Vi2 LCP: I CONFREQ [REQsent] id 166 len 19
*May 12 14:29:46.167: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:46.167: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:46.167: Vi2 LCP: MagicNumber 0x1904DCDE (0x05061904DCDE)
*May 12 14:29:46.167: Vi2 LCP: O CONFACK [REQsent] id 166 len 19
*May 12 14:29:46.167: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:46.167: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:46.167: Vi2 LCP: MagicNumber 0x1904DCDE (0x05061904DCDE)
*May 12 14:29:46.167: Vi2 LCP: I CONFACK [ACKsent] id 97 len 10
*May 12 14:29:46.167: Vi2 LCP: MagicNumber 0x23368E7E (0x050623368E7E)
*May 12 14:29:46.167: Vi2 LCP: State is Open
*May 12 14:29:46.167: Vi2 PPP: Phase is AUTHENTICATING, by the peer
*May 12 14:29:46.175: Vi2 CHAP: I CHALLENGE id 1 len 35 from "bras-red1.nt-b"
*May 12 14:29:46.175: Vi2 CHAP: Unable to authenticate for peer
*May 12 14:29:46.179: Vi2 PPP: Sending Acct Event[Down] id[32]
*May 12 14:29:46.179: Vi2 PPP: Phase is TERMINATING
LDIS-ROUTER#no debug ppp negotiation
*May 12 14:29:46.179: Vi2 LCP: O TERMREQ [Open] id 98 len 4
*May 12 14:29:46.187: Vi2 LCP: I TERMACK [TERMsent] id 98 len 4
*May 12 14:29:46.187: Vi2 LCP: State is Closed
*May 12 14:29:46.187: Vi2 PPP: Phase is DOWN
*May 12 14:29:46.187: Vi2 PPP: Phase is ESTABLISHING, Passive Open
*May 12 14:29:46.187: Vi2 LCP: State is Listen
*May 12 14:29:46.191: Vi2 LCP: I TERMREQ [Listen] id 1 len 4
*May 12 14:29:46.191: Vi2 LCP: O TERMACK [Listen] id 1 len 4
LDIS-ROUTER#no debug ppp negotiation
*May 12 14:29:48.175: Vi2 LCP: TIMEout: State Listen
*May 12 14:29:48.175: Vi2 PPP: No remote authentication for call-out
*May 12 14:29:48.175: Vi2 LCP: O CONFREQ [Listen] id 99 len 10
*May 12 14:29:48.175: Vi2 LCP: MagicNumber 0x2336977F (0x05062336977F)
*May 12 14:29:48.211: Vi2 LCP: I CONFREQ [REQsent] id 86 len 19
*May 12 14:29:48.211: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:48.211: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:48.211: Vi2 LCP: MagicNumber 0x4B9957EE (0x05064B9957EE)
*May 12 14:29:48.211: Vi2 LCP: O CONFACK [REQsent] id 86 len 19
*May 12 14:29:48.211: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:48.211: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:48.211: Vi2 LCP: MagicNumber 0x4B9957EE (0x05064B9957EE)
*May 12 14:29:48.215: Vi2 LCP: I CONFACK [ACKsent] id 99 len 10
*May 12 14:29:48.215: Vi2 LCP: MagicNumber 0x2336977F (0x05062336977F)
*May 12 14:29:48.215: Vi2 LCP: State is Open
*May 12 14:29:48.215: Vi2 PPP: Phase is AUTHENTICATING, by the peer
*May 12 14:29:48.223: Vi2 CHAP: I CHALLENGE id 1 len 35 from "bras-red1.nt-b"
*May 12 14:29:48.223: Vi2 CHAP: Unable to authenticate for peer
*May 12 14:29:48.223: Vi2 PPP: Sending Acct Event[Down] id[33]
*May 12 14:29:48.223: Vi2 PPP: Phase is TERMINATING
LDIS-ROUTER#no debug ppp negotiation
*May 12 14:29:48.223: Vi2 LCP: O TERMREQ [Open] id 100 len 4
*May 12 14:29:48.231: Vi2 LCP: I TERMACK [TERMsent] id 100 len 4
*May 12 14:29:48.231: Vi2 LCP: State is Closed
*May 12 14:29:48.231: Vi2 PPP: Phase is DOWN
*May 12 14:29:48.231: Vi2 PPP: Phase is ESTABLISHING, Passive Open
*May 12 14:29:48.231: Vi2 LCP: State is Listen
*May 12 14:29:48.231: Vi2 LCP: I TERMREQ [Listen] id 1 len 4
*May 12 14:29:48.231: Vi2 LCP: O TERMACK [Listen] id 1 len 4
*May 12 14:29:49.179: Vi2 UNKNOWN(0xAAAA): LCP not open, discarding packet
LDIS-ROUTER#no debug ppp negotiation
*May 12 14:29:50.223: Vi2 LCP: TIMEout: State Listen
*May 12 14:29:50.223: Vi2 PPP: No remote authentication for call-out
*May 12 14:29:50.223: Vi2 LCP: O CONFREQ [Listen] id 101 len 10
*May 12 14:29:50.223: Vi2 LCP: MagicNumber 0x23369F80 (0x050623369F80)
*May 12 14:29:50.523: Vi2 LCP: I CONFREQ [REQsent] id 230 len 19
*May 12 14:29:50.523: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:50.523: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:50.523: Vi2 LCP: MagicNumber 0x4D806304 (0x05064D806304)
*May 12 14:29:50.523: Vi2 LCP: O CONFACK [REQsent] id 230 len 19
*May 12 14:29:50.523: Vi2 LCP: MRU 1500 (0x010405DC)
*May 12 14:29:50.523: Vi2 LCP: AuthProto CHAP (0x0305C22305)
*May 12 14:29:50.523: Vi2 LCP: MagicNumber 0x4D806304 (0x05064D806304)
*May 12 14:29:50.523: Vi2 LCP: I CONFACK [ACKsent] id 101 len 10
*May 12 14:29:50.523: Vi2 LCP: MagicNumber 0x23369F80 (0x050623369F80)
*May 12 14:29:50.523: Vi2 LCP: State is Open
*May 12 14:29:50.523: Vi2 PPP: Phase is AUTHENTICATING, by the peer
*May 12 14:29:50.531: Vi2 CHAP: I CHALLENGE id 1 len 35 from "bras-red1.nt-b"
*May 12 14:29:50.531: Vi2 CHAP: Unable to authenticate for peer
*May 12 14:29:50.531: Vi2 PPP: Sending Acct Event[Down] id[34]
*May 12 14:29:50.531: Vi2 PPP: Phase is TERMINATING
LDIS-ROUTER#no debug ppp negotiation
PPP protocol negotiation debugging is off
LDIS-ROUTER#
*May 12 14:29:50.531: Vi2 LCP: O TERMREQ [Open] id 102 len 4
*May 12 14:29:50.539: Vi2 LCP: I TERMACK [TERMsent] id 102 len 4
*May 12 14:29:50.539: Vi2 LCP: State is Closed
*May 12 14:29:50.539: Vi2 PPP: Phase is DOWN
*May 12 14:29:50.539: Vi2 PPP: Phase is ESTABLISHING, Passive Open
*May 12 14:29:50.539: Vi2 LCP: State is Listen
*May 12 14:29:50.543: Vi2 LCP: I TERMREQ [Listen] id 1 len 4
*May 12 14:29:50.543: Vi2 LCP: O TERMACK [Listen] id 1 len 4
LDIS-ROUTER#

Try putting


Put that on the dialer interface, I have read before that the setups on the homehub lines dont need a user/pass, what is happening is that the BT BRAS is sending you a authentication request and because you dont have a chap password or a local user account configured for the bras name it is killing the ppp negotiation.

_________________
---
David
CCIE R&S #38338, CCIP, CCNP

http://networkbroadcast.co.uk - My Blog
http://twitter.com/davidrothera

BRILL! that worked... many thanks for that.

If you don't mind I wouldn't mind using your tech knowledge again...

2 questions

1) I can only access the internet using static IP... any way of having dynamic and enable DHCP?

2)

I have connected an AP but currently have no training on this but would like to get it working as part of my setup...

I can access the WAP and the GUI which is great, I just can't access the WEB... feels like I'm starting all over again... I have not set up and security as yet....

Here is my AP and Switch config currently connected to GI1/0/32 on the switch...

SWITCH

LDIS-SWITCH#show run
Building configuration...

Current configuration : 2740 bytes
!
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname LDIS-SWITCH
!
enable secret 5 $1$26EG$bG4nJjUixlFXZbi0bPh8N1
!
username Luke password 7 070C285F4D06
no aaa new-model
switch 1 provision ws-c3750g-48ps
system mtu routing 1500
ip subnet-zero
no ip domain-lookup
ip domain-name ldis.com
!
!
!
!
no file verify auto
spanning-tree mode pvst
spanning-tree extend system-id
!
vlan internal allocation policy ascending
!
interface GigabitEthernet1/0/1
!
interface GigabitEthernet1/0/2
!
interface GigabitEthernet1/0/3
!
interface GigabitEthernet1/0/4
!
interface GigabitEthernet1/0/5
!
interface GigabitEthernet1/0/6
!
interface GigabitEthernet1/0/7
!
interface GigabitEthernet1/0/8
!
interface GigabitEthernet1/0/9
!
interface GigabitEthernet1/0/10
!
interface GigabitEthernet1/0/11
!
interface GigabitEthernet1/0/12
!
interface GigabitEthernet1/0/13
!
interface GigabitEthernet1/0/14
!
interface GigabitEthernet1/0/15
!
interface GigabitEthernet1/0/16
!
interface GigabitEthernet1/0/17
!
interface GigabitEthernet1/0/18
!
interface GigabitEthernet1/0/19
!
interface GigabitEthernet1/0/20
!
interface GigabitEthernet1/0/21
!
interface GigabitEthernet1/0/22
!
interface GigabitEthernet1/0/23
!
interface GigabitEthernet1/0/24
!
interface GigabitEthernet1/0/25
!
interface GigabitEthernet1/0/26
!
interface GigabitEthernet1/0/27
!
interface GigabitEthernet1/0/28
!
interface GigabitEthernet1/0/29
!
interface GigabitEthernet1/0/30
!
interface GigabitEthernet1/0/31
!
interface GigabitEthernet1/0/32
!
interface GigabitEthernet1/0/33
!
interface GigabitEthernet1/0/34
!
interface GigabitEthernet1/0/35
!
interface GigabitEthernet1/0/36
!
interface GigabitEthernet1/0/37
!
interface GigabitEthernet1/0/38
!
interface GigabitEthernet1/0/39
!
interface GigabitEthernet1/0/40
!
interface GigabitEthernet1/0/41
!
interface GigabitEthernet1/0/42
!
interface GigabitEthernet1/0/43
!
interface GigabitEthernet1/0/44
!
interface GigabitEthernet1/0/45
!
interface GigabitEthernet1/0/46
!
interface GigabitEthernet1/0/47
!
interface GigabitEthernet1/0/48
!
interface GigabitEthernet1/0/49
!
interface GigabitEthernet1/0/50
!
interface GigabitEthernet1/0/51
!
interface GigabitEthernet1/0/52
!
interface Vlan1
ip address 192.168.1.100 255.255.255.0
!
ip default-gateway 192.168.1.254
ip classless
ip http server
!
!
control-plane
!
banner motd ^C
^C
!
line con 0
exec-timeout 5 0
password 7 030752180500
logging synchronous
login
line vty 0 4
password 7 030752180500
logging synchronous
login
transport input telnet
line vty 5 15
login
!
end




WAP


ap#show run
Building configuration...

Current configuration : 1399 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
!
hostname ap
!
enable secret 5 $1$96sl$6Wi/p3YBlhJ/GVwjm6UBP.
!
username Cisco password 7 112A1016141D
ip subnet-zero
!
dot11 arp-cache optional
!
bridge irb
!
!
interface Dot11Radio0
no ip address
no ip route-cache
!
ssid CISCO WAP L&D
authentication open
guest-mode
infrastructure-ssid optional
wpa-psk ascii 7 047F0A105E32644B071D5605
!
speed basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
rts threshold 2312
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
!
interface FastEthernet0
ip address 192.168.1.65 255.255.255.0
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
!
interface BVI1
ip address 192.168.1.65 255.255.255.0
no ip route-cache
!
ip default-gateway 192.168.1.254
ip http server
ip http help-path http://www.cisco.com/warp/public/779/sm ... ivory/1100
ip radius source-interface BVI1
bridge 1 route ip
!
!
line con 0
line vty 0 4
login local
line vty 5 15
login
!
end

Ok, thanks for your valuble time though

Hi,

for DHCP you need a DHCP Pool



regards
Michael

_________________
CCNA
http://www.netzwerkblog.info (German IT Blog)