Hi guys,
i've some trouble configuring a TDM switch PRI-to-PRI from Telco to an RMX 1500.
After a lot of hours spent on configuration now i can receive and make call from the RMX, but only two channels. When I try to make a third call I get "Cause i = 0x82AC - Requested circuit/channel not available"
This is the HW configuration:
Cisco 2811 (IOS Version 12.4(25c)) with 2 VWIC2-2MFT-T1/E1, 16-PVDM2 and 64-PVDM2
on the first VWIC i've two Telco PRI (each with 15 bi-directional channel), on the second VWIC i've connected with E1 cross-cable the RMX 1500 with 6 timeslots configured
This router already doing VoIP translation from the Telco PRI to an Asterisk PBX (fax and DID).
There are some logs for a call with more than two channels from the RMX
Code:
Mar 28 08:39:43.426: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2701
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723849'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:39:43.450: ISDN Se0/3/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xA701
Channel ID i = 0xA98381
Exclusive, Channel 1
Mar 28 08:39:45.614: ISDN Se0/3/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xA701
Progress Ind i = 0x8188 - In-band info or appropriate now available
Mar 28 09:39:46: %ISDN-6-CONNECT: Interface Serial0/0/0:14 is now connected to 00441753723849 N/A
Mar 28 09:39:46: %ISDN-6-CONNECT: Interface Serial0/3/0:0 is now connected to 990 N/A
Mar 28 08:39:46.258: ISDN Se0/3/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xA701
Progress Ind i = 0x8188 - In-band info or appropriate now available
Mar 28 08:39:46.270: ISDN Se0/3/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x2701
Mar 28 08:39:51.886: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2801
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98382
Exclusive, Channel 2
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723849'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:39:51.906: ISDN Se0/3/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xA801
Channel ID i = 0xA98382
Exclusive, Channel 2
Mar 28 08:39:52.406: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2901
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723645'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:39:52.418: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xA901
Cause i = 0x82AC - Requested circuit/channel not available
Mar 28 08:39:52.906: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2A01
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723645'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:39:52.918: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xAA01
Cause i = 0x82AC - Requested circuit/channel not available
Mar 28 08:39:53.414: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2B01
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723853'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:39:53.430: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xAB01
Cause i = 0x82AC - Requested circuit/channel not available
VGW01#
Mar 28 08:39:53.938: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2C01
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723853'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:39:53.954: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xAC01
Cause i = 0x82AC - Requested circuit/channel not available
Mar 28 09:39:54: %ISDN-6-CONNECT: Interface Serial0/0/0:13 is now connected to 00441753723849 N/A
Mar 28 08:39:54.838: ISDN Se0/3/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xA801
Progress Ind i = 0x8188 - In-band info or appropriate now available
Mar 28 09:39:54: %ISDN-6-CONNECT: Interface Serial0/3/0:1 is now connected to 990 N/A
Mar 28 08:39:54.854: ISDN Se0/3/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xA801
Progress Ind i = 0x8188 - In-band info or appropriate now available
Mar 28 08:39:54.866: ISDN Se0/3/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x2801
Mar 28 08:40:07.479: ISDN Se0/3/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x2701
Cause i = 0x8090 - Normal call clearing
Mar 28 08:40:07.483: ISDN Se0/3/0:15 Q931: RX <- DISCONNECT pd = 8 callref = 0x2801
Cause i = 0x8090 - Normal call clearing
Mar 28 09:40:07: %ISDN-6-DISCONNECT: Interface Serial0/3/0:0 disconnected from 990 , call lasted 21 seconds
Mar 28 09:40:07: %ISDN-6-DISCONNECT: Interface Serial0/3/0:1 disconnected from 990 , call lasted 12 seconds
Mar 28 08:40:07.491: ISDN Se0/3/0:15 Q931: TX -> RELEASE pd = 8 callref = 0xA701
Mar 28 08:40:07.491: ISDN Se0/3/0:15 Q931: TX -> RELEASE pd = 8 callref = 0xA801
Mar 28 09:40:07: %ISDN-6-DISCONNECT: Interface Serial0/0/0:14 disconnected from 00441753723849 , call lasted 21 seconds
Mar 28 08:40:07.507: ISDN Se0/3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x2701
Mar 28 08:40:07.515: ISDN Se0/3/0:15 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x2801
Mar 28 09:40:07: %ISDN-6-DISCONNECT: Interface Serial0/0/0:13 disconnected from 00441753723849 , call lasted 12 seconds
Mar 28 08:40:36.535: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2D01
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723849'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:40:36.559: ISDN Se0/3/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xAD01
Channel ID i = 0xA98381
Exclusive, Channel 1
Mar 28 08:40:38.583: ISDN Se0/3/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xAD01
Progress Ind i = 0x8188 - In-band info or appropriate now available
Mar 28 09:40:38: %ISDN-6-CONNECT: Interface Serial0/0/0:14 is now connected to 00441753723849 N/A
Mar 28 09:40:39: %ISDN-6-CONNECT: Interface Serial0/3/0:0 is now connected to 990 N/A
Mar 28 08:40:39.131: ISDN Se0/3/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xAD01
Progress Ind i = 0x8188 - In-band info or appropriate now available
Mar 28 08:40:39.371: ISDN Se0/3/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x2D01
Mar 28 09:40:44: %ISDN-6-CONNECT: Interface Serial0/0/0:2 is now connected to 141275158 N/A
Mar 28 09:40:44: %ISDN-6-CONNECT: Interface Serial0/0/0:3 is now connected to 3355385688 N/A
Mar 28 08:40:44.727: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2E01
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98382
Exclusive, Channel 2
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723849'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:40:44.747: ISDN Se0/3/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xAE01
Channel ID i = 0xA98382
Exclusive, Channel 2
Mar 28 08:40:45.227: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x2F01
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723645'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:40:45.239: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xAF01
Cause i = 0x82AC - Requested circuit/channel not available
Mar 28 08:40:45.747: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3001
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723645'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:40:45.759: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB001
Cause i = 0x82AC - Requested circuit/channel not available
VGW01#
Mar 28 08:40:46.307: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3101
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723853'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:40:46.563: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB101
Cause i = 0x82AC - Requested circuit/channel not available
Mar 28 08:40:46.807: ISDN Se0/3/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3201
Bearer Capability i = 0x8890
Standard = CCITT
Transfer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98383
Exclusive, Channel 3
Calling Party Number i = 0x80, '990'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '00441753723853'
Plan:Unknown, Type:Unknown
Sending Complete
Mar 28 08:40:46.827: ISDN Se0/3/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB201
Cause i = 0x82AC - Requested circuit/channel not available
the other called number are connected to the same endpoint, they are pushed from far end to make a multi channel video conf at 384kbit.. just to clarify that the call records are for a video call to number 00441753723849 (Polycom test)
this is the configuration of the router (removed password and changed phone number)
Code:
version 12.4
service timestamps debug datetime msec
service timestamps log datetime localtime
no service password-encryption
!
hostname VOIPGW1
!
boot-start-marker
boot-end-marker
!
card type e1 0 0
card type e1 0 3
enable password cisco
!
no aaa new-model
clock timezone CET 1
clock summer-time CET recurring 1 Sun Apr 2:00 last Sun Oct 2:00
network-clock-participate wic 0
network-clock-participate wic 3
!
!
ip cef
!
!
no ip domain lookup
isdn switch-type primary-net5
!
voice-card 0
dspfarm
dsp services dspfarm
!
!
voice call send-alert
voice call convert-discpi-to-prog
voice call carrier capacity active
voice rtp send-recv
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol pass-through g711ulaw
modem passthrough nse codec g711ulaw
sip
rel1xx disable
header-passing
!
!
!
voice class codec 1
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 g729br8
codec preference 4 g729r8
!
!
!
!
!
!
!
!
voice translation-rule 100
rule 1 /^/ /0/ type unknown unknown
rule 2 /^/ /0/ type national national
rule 3 /^/ /000/ type international international
!
voice translation-rule 201
rule 1 /500/ /06567801/
rule 2 /599/ /06567801/
rule 3 /562/ /06567801/
rule 4 /502/ /0656780100/
rule 5 /503/ /0656780100/
rule 6 /504/ /0656780100/
rule 7 /505/ /0656780100/
rule 8 /507/ /0656780100/
rule 9 /555/ /0656780100/
rule 10 /556/ /0656780100/
rule 11 /588/ /0656780100/
rule 12 /589/ /0656780100/
rule 13 /597/ /0656780100/
rule 14 /1.../ /0656780100/
rule 15 /\(...\)/ /0656780\1/
!
voice translation-rule 202
rule 1 /500/ /061234561/
rule 2 /599/ /061234561/
rule 3 /562/ /061234561/
rule 4 /\(...\)/ /06123456\1/
!
voice translation-rule 203
rule 1 /656780990/ /990/
!
!
voice translation-profile InboundCallingParty
translate calling 100
!
voice translation-profile OUTGOING
translate calling 201
!
voice translation-profile OUTGOING_2
translate calling 202
!
voice translation-profile OUTGOING_RMX
translate calling 203
!
!
!
!
controller E1 0/0/0
pri-group timeslots 1-16
!
controller E1 0/0/1
pri-group timeslots 1-16
!
controller E1 0/3/0
clock source internal
pri-group timeslots 1-6,16
!
controller E1 0/3/1
!
ip ssh version 2
!
translation-rule 201
!
!
!
!
interface FastEthernet0/0
description MAIN INTERFACE TO CHAOS
ip address 10.x.x.x 255.255.255.0
duplex auto
speed auto
!
interface FastEthernet0/1
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0/0/0:15
description ** PRI TELCO 0656780 **
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving T302 4000
isdn incoming-voice voice
isdn send-alerting
no cdp enable
!
interface Serial0/0/1:15
description ** PRI TELCO 06123456 **
no ip address
encapsulation hdlc
no logging event link-status
isdn switch-type primary-net5
isdn overlap-receiving T302 4000
isdn incoming-voice voice
no cdp enable
!
interface Serial0/3/0:15
description ** TO RMX1500 0656780990-7 **
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving T302 3000
isdn protocol-emulate network
isdn incoming-voice voice
isdn send-alerting
no cdp enable
!
ip forward-protocol nd
!
!
ip http server
no ip http secure-server
!
!
!
control-plane
!
!
!
voice-port 0/0/0:15
translation-profile incoming InboundCallingParty
!
voice-port 0/3/0:15
!
voice-port 0/0/1:15
translation-profile incoming InboundCallingParty
!
!
!
!
!
dial-peer voice 1 pots
description *** PEER incoming number 0656780 ***
incoming called-number 656780...
direct-inward-dial
!
dial-peer voice 2 pots
description *** PEER incoming number 06123456 ***
incoming called-number 6726534...
direct-inward-dial
!
dial-peer voice 3 pots
description *** PEER incoming number 06123456 ***
incoming called-number 6726534
direct-inward-dial
!
dial-peer voice 4 pots
description *** PEER incoming number 0612345611 ***
incoming called-number 67265341
direct-inward-dial
!
dial-peer voice 5 pots
description *** PEER incoming number 0656780 ***
incoming called-number 656780
direct-inward-dial
!
dial-peer voice 300 voip
description *** PBX IVR to CM02 06123456 ***
preference 1
destination-pattern 67265341
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.8
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 301 voip
description *** PBX IVR to CM01 06123456 ***
preference 1
destination-pattern 67265341
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.7
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 302 voip
description *** PBX IVR to CM02 06123456 ***
preference 1
destination-pattern 6726534
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.8
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 303 voip
description *** PBX IVR to CM01 06123456 ***
preference 2
destination-pattern 6726534
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.7
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 304 voip
description *** Match timeout to PBX CM02 0656780 ***
preference 1
destination-pattern 656780T
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.8
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 305 voip
description *** Match timeout to PBX CM01 0656780 ***
preference 2
destination-pattern 656780T
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.7
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 306 voip
description *** DID to CM02 0656780 ***
preference 1
destination-pattern 656780[5-6]..
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.8
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 307 voip
description *** DID to CM01 0656780 ***
preference 2
destination-pattern 656780[5-6]..
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.7
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 1002 voip
description *** 800 to CM02 - PRI TELCO 06123456 - DID 201 ***
destination-pattern 6726534201
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.8
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 1003 voip
description *** 800 to CM01 - PRI TELCO 06123456 - DID 201 ***
destination-pattern 6726534201
progress_ind setup enable 3
session protocol sipv2
session target ipv4:10.100.253.7
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
no vad
!
dial-peer voice 1004 voip
description *** 199 to CM01 - FAX - PRI TELCO 0656780 - DID 101 **
max-conn 4
destination-pattern 656780101
progress_ind setup enable 3
rtp payload-type cisco-codec-fax-ack 103
rtp payload-type cisco-codec-fax-ind 102
rtp payload-type nte 96
session protocol sipv2
session target ipv4:10.100.253.7
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
fax rate disable
fax protocol none
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
!
dial-peer voice 1005 voip
description *** 199 to CM02 - FAX - PRI TELCO 06123456 - DID 101 **
max-conn 4
destination-pattern 6726534101
progress_ind setup enable 3
rtp payload-type cisco-codec-fax-ack 103
rtp payload-type cisco-codec-fax-ind 102
rtp payload-type nte 96
session protocol sipv2
session target ipv4:10.100.253.8
session transport udp
dtmf-relay rtp-nte
no call fallback
codec g711ulaw
fax rate disable
fax protocol none
ip qos dscp cs5 media
ip qos dscp cs4 signaling
no vad
!
dial-peer voice 2000 pots
description *** PRI TELCO 0656780 ***
translation-profile outgoing OUTGOING
preference 1
destination-pattern .T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
port 0/0/0:15
!
dial-peer voice 2001 pots
description *** PRI TELCO 06123456 ***
translation-profile outgoing OUTGOING_2
preference 2
destination-pattern 11.T
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
fax rate disable
port 0/0/1:15
!
dial-peer voice 7 pots
destination-pattern 65678099[0-7]
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/3/0:15
forward-digits all
!
dial-peer voice 8 pots
destination-pattern 990
progress_ind setup enable 3
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/3/0:15
forward-digits all
!
sip-ua
retry invite 4
timers trying 300
!
!
line con 0
logging synchronous
line aux 0
line vty 0 4
logging synchronous
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
ntp clock-period 17180079
ntp server 10.x.x.x
!
end
and a "sh isdn services"
Code:
#sh isdn service
PRI Channel Statistics:
ISDN Se0/0/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 0
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
ISDN Se0/0/1:15, Channel [1-31]
Configured Isdn Interface (dsl) 1
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
ISDN Se0/3/0:15, Channel [1-31]
Configured Isdn Interface (dsl) 2
Channel State (0=Idle 1=Proposed 2=Busy 3=Reserved 4=Restart 5=Maint_Pend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
Service State (0=Inservice 1=Maint 2=Outofservice 8=MaintPend 9=OOSPend)
Channel : 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
State : 0 0 0 0 0 0 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
hope someone can help me
many thanks
Register
Search 
Login
